Matthew Celmer
My chimney needed replacing before I could sell the house. The replaced the cap and went above and beyond to fix a few other issues on roof. 5 stars plus.Read it on Google(opens in a new tab)
Repair and restoration
The chase cover, also called a chase cap or chase top, is the metal lid on a framed chimney chase. Once it rusts through, water gets in. We measure yours and replace it with one that actually fits. Chase cover replacement starts at $1,395.

Rated 5.0 out of 5 on Google
Matthew Celmer
My chimney needed replacing before I could sell the house. The replaced the cap and went above and beyond to fix a few other issues on roof. 5 stars plus.Read it on Google(opens in a new tab)
Nathan Michael
Such a great experience and pretty easy we wanted to get our furnace up and running after 15 years. Tell me a couple hours and some cleaning. What was your name again Juda was very professional and very fast. The cleaning went well. The new cap spectacularRead it on Google(opens in a new tab)
Levi Bell
Great experience with Moses Chimney! They replaced my old, flimsy galvanized chase cover with a high-quality stainless steel one, which is a huge upgrade. They were fast, efficient, and did an excellent job. Very friendly and professional as well. Everything looks great, and I’m very happy with the work. Highly recommend!Read it on Google(opens in a new tab)
Chase covers are made to the size of your chase, so we measure before we quote.
The cover and what it's made of, laid out item by item with the job total.
The old cover comes off, and the new one goes on and gets sealed.
A framed chimney is built of wood and covered in siding to match the house, with a metal chase cover on top. Galvanized covers rust with time. Rust streaks running down the siding under the cover are usually the first thing homeowners notice.
We measure the chase and replace the old cover with one made to fit it.
People use the names loosely, and plenty of homeowners call the chase cover a chase cap. The chase cover is the flat metal panel that closes off the whole top of the chase. The chimney cap is the smaller hood with mesh sides that sits on the flue pipe coming up through it. The cover keeps water out of the wood framing, and the cap keeps rain, birds and animals out of the flue. When we replace a cover, the cap comes off and goes back on, or gets replaced too if it has rusted. Caps have their own page.
A cover that sags in the middle and holds a puddle, rust around the flue openings, rust streaks on the siding, or water stains on the ceiling or wall near a factory-built fireplace. Our guide to rusted chase covers and missing caps explains what those rust streaks mean.
Replacing a chase cover with a stainless one that has a single flue opening starts at $1,395. The price goes by the length and width of the chase, so we measure before we quote. Covers with two or three openings are priced the same way, by size. A painted or colored finish adds 25%. If the wood frame under the old cover has rotted, repairing it runs $895 to $2,349, and we show you the frame before any of that work is done.
Supply shops sell chase covers online, often for a few hundred dollars. Those are stock sizes, or covers made to measurements you take and installed by you. Our price covers measuring the chase, a cover built to its real shape, taking the old cover off, the work on the roof, sealing, and putting the storm collar and cap back. If we inspected the chimney first, the $49 inspection fee comes off the job.
We measure the top of the chase on all four sides and corner to corner, since a chase framed a little out of square needs a cover built to its real shape. We note where each flue comes through and the size of each pipe. The skirt, the part that folds down over the siding, has to reach past the top edge of the siding and end in a drip edge so water drops off instead of running down the chase.
Galvanized steel is ordinary steel with a zinc coating. Once the zinc wears away, the steel underneath rusts. Stainless steel doesn't depend on a coating to resist rust, so there's no layer to wear through. Copper is an option where the look of the roofline matters. It weathers to brown and eventually green.
A lot of builder-grade covers are flat sheets. Snow sits on them for months, and when it melts, the water pools around the flue openings. A thin flat cover can also start to sag under the weight.
The covers we install have cross breaks pressed into the top so water runs out to the edges, a raised collar around each flue opening, and a drip edge on the skirt. That's how cover makers such as Chim Cap Corp build their stainless covers.
We take off the cap and storm collar, pull the old cover and check the wood framing on top of the chase. If the wood is soft, we show you before the new cover goes on, since a new cover over rotted framing won't fix the leak. The new cover is screwed through the skirt into the framing and sealed at the fasteners. The storm collar goes back on and is sealed to the flue pipe, then the cap goes on top.
A made-to-measure cover usually takes one to two weeks to be built after we measure. Installing it is usually an hour or two on the roof, on a dry day. We take the old cover and cap away with us.
What we charge for this work. Where a price depends on size, we measure on the visit and give you the total in writing before anything starts.
Where a price is a range, these decide where your job falls in it.


Before: Rusted chase cover and cap. After: Chase painted, new stainless cover and cap.


Before: Cracked crown around the vent pipe. After: New stainless cover and cap.
More in questions and answers.
Repairs start with an inspection. We show you what we found, go over the options, and send you a written quote. Each service page lists what we charge for that work. We'll give you a price before starting any work, and nothing starts until you've approved the quote. Most jobs need a deposit before we order parts or materials.
Yes. Send us pictures of your chimney and we can give you a rough idea of what the work involves. Any estimate from pictures is preliminary and is not a final price until we visit the property and inspect the job in person.
A standard chimney inspection is $49. The inspection fee is credited toward any work we perform. A camera inspection is $75, and if work is needed on the inspected flue, the camera inspection fee is credited toward that work.

B-vent caps, standard fireplace caps and multi-flue caps, plus cap repair and net installation.
From $235

Cracked and crumbling crowns repaired, or rebuilt when they're too far gone to patch.
From $249

Water repellent for chimney masonry, applied once the joints and crown are sound.
From $795
Pick a day and a 3-hour arrival window online. If you'd rather talk it through, call (248) 266-9991.
Updated